features n working voltage 3.3 v n smt - dfn package n low capacitance - 4 pf n iec 61000-4-2 (esd) n iec 61000-4-4 (eft) n iec 61000-4-5 (surge) applications n firewire, t1/e1, t3/e3 chip side protection n digital visual interface (dvi) n ethernet 10/100/1000 base t n high speed port protection n portable electronics absolute maximum ratings, t a = 25 c (unless otherwise noted) CDDFN10-3304NA - tvs/steering diode array *rohs directive 2002/95/ec jan. 27, 2003 including annex and rohs recast 2011/65/eu june 8, 2011. specifcations are subject to change without notice. users should verify actual device performance in their specifc applications. the products described herein and this document are subject to specifc disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf . parameter symbol CDDFN10-3304NA unit peak pulse current (t p = 8/20 s) per iec 61000-4-5 i pp 25 a esd protection per iec 61000-4-2 contact discharge air discharge 30 30 kv kv eft protection per iec 61000-4-4 @ 5/50 ns 40 a storage temperature t stg -55 to +150 oc operating temperature t opr -55 to +125 oc general information the CDDFN10-3304NA device provides esd, eft and surge protection for high speed data ports, assisting compliance with iec 61000-4-2 (esd), iec 61000-4-4 (eft) and iec 61000-4-5 (surge) requirements. the transient voltage suppressor array, protecting up to 4 data lines, offers a working peak voltage of 3.3 v. the dfn-10 packaged device will mount directly onto the industry standard dfn-10 footprint. bourns ? chip diodes are easy to handle with standard pick and place equipment. electrical characteristics (@ t a = 25 c unless otherwise noted) parameter symbol min. typ. max. unit breakdown voltage @ 1 ma v br 3.9 v reverse working peak voltage v rwm 3.3 v leakage current 1 @ v rwm i d 1 a clamping voltage 2 @ i p = 5 a 8/20 s v c 12 v clamping voltage 2 @ i p = 15 a 8/20 s v c 15 v clamping voltage 2 @ i p = 25 a 8/20 s v c 18 v junction capacitance 2 @ 0 v 1 mhz c d 4.0 4.6 pf junction capacitance 3 @ 0 v 1 mhz c io 1.5 2.3 pf note 1: pin 5 to ground. note 2: pin 1,3,7 or 9 to ground. note 3: between pin 1,3,7 and 9. pin 5 pin 1 pin 3 gnd pin 7 pin 9 *rohs compliant lead free *rohs compliant versions available lead free versions are rohs compliant*
20 40 60 80 10 0 12 0 0 03 0 25 20 15 10 5 ipp ? peak pulse current (% of ipp) t ? time (s) test waveform parameters t t = 8 s t d = 20 s t t e t t d = t | i pp /2 18 16 14 12 10 8 6 4 2 0 43 0 peak pulse current (a) 6 clamping voltage (v) 8 10 12 14 16 18 20 22 24 26 28 any i/o pin to another i/o pin any i/o pin to gnd v dd pin to gnd waveform parameters: tr = 8 s td = 20 s 0.0 0.0 0.5 3.5 input capacitance (pf) input voltage (v) 4.5 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 1.0 1.5 2.0 2.5 3.0 v dd = floated v dd = 3.3 v f = 1 mhz, t = 25 c any i/o to gnd 0 2 0 transmission line pulsing (tlp) current (a ) 16 18 14 12 10 8 6 4 1 transmission line pulsing (tlp) voltage (v ) 14 23 45 6 789 10 11 12 13 v_pulse 100 ns tlp_v dut tlp_i + - pulse from a transmission lin e v dd to gnd any i/o pin to another i/o pin i/o to gnd 0 80 02 5 150 % of rated power ambient temperature (c) 100 40 60 80 50 75 100 125 ? ? ?-?? ? ? - ?? ? ?? -? ?? - ? ? ? ? ?? ?
? ?-? ?? ?? ? ? ?? ? -? ?-?? ?? ??? ? ? ? ? ? ? ? ? ?? ? -?? ? ? - ? ?????? ??
rating & characteristic curves pulse waveform typical clamping voltage vs peak pulse current typical transmission line pulsing (tlp) measurement typical voltage vs. capacitance typical power derating curve
3312 - 2 mm smd trimming potentiometer specifcations are subject to change without notice. users should verify actual device performance in their specifc applications. the products described herein and this document are subject to specifc disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf . CDDFN10-3304NA - tvs/steering diode array product dimensions this is a molded dfn10 package with lead free nickel-paladium- gold (ni/pd/au) on the lead frame. it has a fammability rating of ul 94v-0. recommended footprint how to order cd dfn10 - 33 04 na common diode chip diode package dfn10 = dfn-10 package reverse working peak voltage 33 = 3.3 v rwm (volts) number of lines 04 = 4 data lines suffx na = low capacitance 2.45 - 2.55 (0.096 - 0.100) pin 1 indicator pin 1 2.45 - 2.55 (0.096 - 0.100) 2.10 - 2.20 (0.083 - 0.087) 1.85 - 1.95 (0.073 - 0.077) 0.50 (0.020) 0.2 (.008) r 0.50 - 0.60 (0.020 - 0.024) 0.152 (0.006) 2.05 (.081) 1.26 (.050) 3.15 (.124) 1.85 (.073) 2.50 (.100) 0.50 (.020) 0.65 (.026) 0.30 (.012) 1.15 - 1.25 (0.045 - 0.049) 0.35 - 0.45 (0.014 - 0.018) 0.20 - 0.30 (0.008 - 0.012) 2.45 - 2.55 (0.096 - 0.100) pin 1 indicator pin 1 2.45 - 2.55 (0.096 - 0.100) 2.10 - 2.20 (0.083 - 0.087) 1.85 - 1.95 (0.073 - 0.077) 0.50 (0.020) 0.2 (.008) r 0.50 - 0.60 (0.020 - 0.024) 0.152 (0.006) 2.05 (.081) 1.26 (.050) 3.15 (.124) 1.85 (.073) 2.50 (.100) 0.50 (.020) 0.65 (.026) 0.30 (.012) 1.15 - 1.25 (0.045 - 0.049) 0.35 - 0.45 (0.014 - 0.018) 0.20 - 0.30 (0.008 - 0.012) dimensions: mm (inches) pin out typical part marking pin function 1 i/o 2 n.c. 3 i/o 4 n.c. 5 v dd 6 n.c. 7 i/o 8 n.c. 9 i/o 10 n.c. center tab ground 1 ch1 2 nc 3 gnd (center tab) top view ch3 4 nc 5 vdd 6n c 7 ch4 8n c ch2 9 nc 10 334na llll device code: 334na = CDDFN10-3304NA lot traceability code environmental specifcations moisture sensitivity level ................................................................ 3 esd classifcation (hbm) ............................................................. 3b
CDDFN10-3304NA - tvs/steering diode array packaging information ....... ....... ....... ....... ....... ....... ....... ....... pa f e t 120 d 2 d d 1 w 1 c index hole pin 1 location p 0 p 1 w b 10 pitches (min.) direction of feed 10 pitches (min.) end trailer device leader start d the product will be dispensed in tape and reel format (see diagram below). devices are packed in accordance with eia standard rs-481-a. dimensions: mm (inches) item symbol dfn-10 carrier width a 1.2 0.05 (0.047 0.002) carrier length b 2.7 0.05 (0.106 0.002) carrier depth c 0.7 0.05 (0.028 0.002) sprocket hole d 1.5 0.05 (0.059 +0.002) reel outside diameter d 180 3 (7.087 0.118) reel inner diameter d 1 50.0 (1.969) min. feed hole diameter d 2 13.00 0.20 (0.512 0.008) sprocket hole position e 1.75 0.10 (0.069 0.004) punch hole position f 3.50 0.05 (0.138 0.002) punch hole pitch p 4.00 0.10 (0.157 0.004) sprocket hole pitch p 0 4.00 0.10 (0.157 0.004) embossment center p 1 2.00 0.05 (0.079 0.002) overall tape thickness t 0.60 (0.024) max. tape width w 12.3 (0.484) max. reel width w 1 18.4 (0.724) max. quantity per reel -- 3000 10/17 specifcations are subject to change without notice. users should verify actual device performance in their specifc applications. the products described herein and this document are subject to specifc disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf . asia-pacifc: tel: +886-2 2562-4117 email: asiacus@bourns.com europe: tel: +36 88 520 390 email: eurocus@bourns.com the americas: tel: +1-951 781-5500 email: americus@bourns.com www.bourns.com
legal disclaimer notice this legal disclaimer applies to purchasers and users of bourns ? products manufactured by or on behalf of bourns, inc. and its afliates (collectively, bourns). unless otherwise expressly indicated in writing, bourns ? products and data sheets relating thereto are subject to change without notice. users should check for and obtain the latest relevant information before placing orders and should verify that such information is current and complete. the characteristics and parameters of a bourns ? product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on bourns knowledge of typical requirements in generic applications. the characteristics and parameters of a bourns ? product in a user application may vary from the data sheet characteristics and parameters due to a combination of the bourns ? product with other components in the users application or due to the environment of the user application itself. such characteristics and parameters also can and do vary in diferent applications and actual performance may vary over time. users should always verify actual performance of the bourns ? product in their specifc devices and applications, and make their own independent judgments about how much additional test margin to design in to compensate for diferences between laboratory and real world conditions. unless bourns has explicitly designated an individual bourns ? product as meeting the requirements of a particular industry standard (e.g., iso/ts 16949) or a particular qualifcation (e.g., ul listed or recognized), bourns is not responsible for any failure of an individual bourns ? product to meet requirements of such industry standard or such particular qualifcation. users of bourns ? products are responsible for ensuring compliance with safety-related requirements and standards applicable to their applications. bourns ? products are not recommended, authorized or intended for use in nuclear, lifesaving, life-critical or life-sustaining applications, nor in any other applications where failure or malfunction may result in personal injury, death, or severe property or environmental damage. unless expressly and specifcally approved in writing by two authorized bourns representatives on a case-by-case basis, use of any bourns ? products in such unauthorized applications is at the users sole risk. life-critical applications include devices identifed by the u.s. food and drug administration as class iii devices and generally equivalent classifcations outside of the united states. bourns ? standard products that are designed and tested for use in automotive applications will be described on the applicable data sheets as compliant with the applicable aec-q standard. unless expressly and specifcally approved in writing by two authorized bourns representatives on a case-by-case basis, use of any other bourns ? standard products in an automotive application is not recommended, authorized or intended and will be at the users sole risk. bourns ? standard products are not tested to comply with united states federal aviation administration standards generally or any other generally equivalent governmental organization standard applicable to products designed or manufactured for use in aircraft or space applications. bourns ? standard products that are designed and tested for use in aircraft or space applications will be described on the applicable data sheets as compliant with the rtca do-160 standard. unless expressly and specifcally approved in writing by two authorized bourns representatives on a case-by-case basis, use of any other bourns ? standard product in an aircraft or space application is not recommended, authorized or intended and will be at the users sole risk. the use and level of testing applicable to bourns ? custom products shall be negotiated on a case-by-case basis by bourns and the user for which such bourns ? custom products are specially designed. absent a written agreement between bourns and the user regarding the use and level of such testing, the provisions above applicable to bourns ? standard products shall also apply to such bourns ? custom products. users shall not sell, transfer, export or re-export any bourns ? products or technology for use in activities which involve the design, development, production, use or stockpiling of nuclear, chemical or biological weapons or missiles, nor shall they use bourns ? products or technology in any facility which engages in activities relating to such devices. the foregoing restrictions apply to all uses and applications that violate national or inter national prohibitions, including embargos or international regulations. further, bourns ? products, technology or technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes, and bourns ? products may not, without prior authorization from bourns and/or the u.s. government, be resold, transferred, or re-exported to any party not eligible to receive u.s. commodities, software, and technical data. to the maximum extent permitted by applicable law, bourns disclaims (i) any and all liability arising out of the application or use of any bourns ? standard product, (ii) any and all liability, including, without limitation, special, punitive, consequential or incidental damages, and (iii) any and all implied warranties, in cluding implied warranties of ftness for particular purpose, non-infringement and merchantability. for your convenience, copies of this legal disclaimer notice with german, spanish, japanese, t raditional chinese and simplifed chinese bilingual versions are available at: web page: http://www.bourns.com/legal/disclaimers-terms-and-policies pdf: http://www.bourns.com/docs/legal/disclaimer.pdf c1753 10/18/17
|
